[Tips] How to skip the "Connect Joycons" system init screen

How to skip the "Connect Joycons" system init screen

Use case: You are stuck at the system initialize screen with the 'connect joycons' animation but you don't have joycons or one or both rails is broken.

TL;DR for those who already know how to edit system saves: Dump the SystemSettings save 8000000000000050, change the byte at offset 0x29484 from 0 to 1, repack, sign and replace the save.

Tools required:
  •     hactoolnet (fire up your command line skills)
  •     Lockpick_RCM (if you have an existing dump from this console a fresh dump is not required)
  •     TegraExplorer (if you're familiar with HacDiskMount you can use that instead)
  •     HxD (or hex editor of choice, this one is just free, lightweight, capable, and ad-free)


Steps:

  1.     Use Hekate/Nyx and make a full Raw EMMC backup if you never have! This is the first rule of any hacking endeavor.
  2.     If you don't have a key file, use Lockpick_RCM to dump keys from either sysnand or emunand, it doesn't matter which for this purpose. This will dump the key file to SD in /switch/prod.keys.
  3.     Reboot to RCM if needed and push the TegraExplorer payload.
  4.     Use the Volume keys to navigate to either [SYSTEM:/] EMMC (for sysnand) or [SYSTEM:/] EMUMMC (for emunand).
  5.     Acknowledge the warning regarding modifying your system NAND and breathe easy since you made a backup, right? RIGHT? Please go back and do that if you haven't. Press Power to continue.
  6.     Select save (this might take a minute to load if using emunand, especially partition-based).
  7.     Select 8000000000000050, then select Copy to clipboard.
  8.     Navigate back to the main menu by selecting Folder -> previous folder twice.
  9.     Select [SD:/] SD CARD.
  10.     Select Clipboard -> Current folder and wait for the copy to complete.
  11.     Navigate back to the main menu by selecting Folder -> previous folder.
  12.     Select Exit then either reboot to RCM or power off.
  13.     Mount the SD card on your computer either using a card reader or by pushing the Memloader payload (this is always recommended to reduce stress on the SD reader connector component).
  14.     Open a command prompt (eg. press Win+R and type cmd then press Return).
  15.     Navigate to where you unzipped hactoolnet or drag the executable onto the command prompt window (this is a handy trick that makes the next few steps easier; Windows automatically enters the whole path to whatever you drop on it).
  16.     I don't know what drive letter you mounted your SD as, but you do! So I'm going to pretend it's Z: but if it's something else, use that instead.
  17.     If you dragged hactoolnet into the window, you'll have c:\whatever\hactoolnet.exe already populated, so after that, type a space then -t save -k z:\switch\prod.keys z:\8000000000000050 --outdir z:\syssave so your whole command should look like:

    c:\whatever\hactoolnet.exe -t save -k z:\switch\prod.keys z:\8000000000000050 --outdir z:\syssave

    Again, please edit this so it matches your own path to hactoolnet and SD mount point.

   18. Open z:\syssave\file in HxD.
   19. Press Ctrl+G to open the Go to Offset dialogue, and type in the number 29484 then select OK. The cursor should be hovering over a byte that reads 00.
   20. Type 01 then press Ctrl+S to Save.
   21. Go back to your command prompt and similarly enter c:\whatever\hactoolnet.exe -t save -k z:\switch\prod.keys z:\8000000000000050 --replacefile file z:\syssave\file. Verify that hactoolnet prints:
Replaced file /file
Successfully signed save file with key <key>
    22. Eject the SD from the computer, reinsert into console, however you did it, get back to RCM with the SD inserted and inject TegraExplorer.
    23. Select [SD:/] SD CARD.
    24. Select 8000000000000050, then select Copy to clipboard.
    25. Navigate back to the main menu by selecting Folder -> previous folder.
    26. Use the Volume keys to navigate to either [SYSTEM:/] EMMC (for sysnand) or [SYSTEM:/] EMUMMC (for emunand), making the same choice as in Step 4.
    27. Acknowledge the warning, press Power to continue.
    28. Select save (as before, this might take a minute to load if using emunand, especially partition-based).
    29. Select 8000000000000050, then select Delete file.
    30. Acknowledge the warning, press Power to delete, wait for completion.
    31. Navigate back to the main menu by selecting Folder -> previous folder twice.
    32. Select Exit then do whatever you need to do to reboot, with or without CFW.
    33. You're done! Instead of the joycon connect animation you should get a screen asking you to accept the Eula then reboot, after which you should be in the OS!

Post a Comment

0 Comments